Thursday, July 22, 2021

Cheap water heater, but is it really cheaper?

With today's economy and people needing to find cheaper and more efficient heating and cooling alternatives, it's a good idea to look for a cheap water heater.

After all, most of us will admit that we want to be more fuel efficient and take better care of the environment, right?

With that in mind, many of us are looking for cheap heaters to cut down on our water heating bills.

But let's see if the traditional tank heater is really cheaper.

These cheap water heaters may not be as cheap as you might think

You can find a good size tank heater for around $ 200 that is sold at your local home improvement store.

เครื่องทําน้ําอุ่น


They are typically in the range of 40 to 50 gallons and will heat your water so you have as many gallons available when you need to wash up, take a bath, wash the dog or whatever.

The tank unit works by heating that amount of water and then keeping it ready if you need it. This means that the water is kept at a constant temperature of 160 degrees (or whatever temperature you set it) at all times of the day.

So the heater turns on and off all day and night to keep the water warm. Your electricity bill reflects this.

It seems that cheap water heater might not be that cheap, right? Oh!

Loss of hot water and limited supply

Traditional tank heaters constantly lose heat. When the tank is filled with hot เครื่องทําน้ําอุ่น, the heat is lost through the heat, which basically leaks out. Imagine a cup of tea or coffee. When tea or coffee gets cold, this heat is lost.

Even if your heater is insulated, there is still a significant heat loss when it radiates. This heat loss can be up to 20 to 40%.

Another disadvantage of "cheap" traditional water heaters is that hot water can run dry. If a person takes a shower, they can consume all the water that is hot. Then the next person has to wait 30 to 60 minutes to shower with hot water.

What a bore!

An efficient alternative to cheap water heaters

Consider a tankless heater. You may have also heard of these so-called "utility systems" heaters, "as needed" heaters or "electric instantaneous water heaters."

What this means is that the heater provides hot water when you need it.

No water is stored. When you turn on the hot water tap, the heating system heats up the water as needed so you can shower for as long as you want, and then lets the next person also take a shower without running out of hot water.

Why is this a better alternative to the cheap tank heaters found in Menards or Home Depot?

In short, cheap water heaters turn out not to be cheap in the long run.

Benefits of "cheap water heaters"

It may be a good idea to consider what you think is a cheap water heater, as research has shown that what may have been the cheap heater initially may not be the cheap heater in the long run.

Tank heater for the place of use can be more expensive in the beginning. Think about it though: heating appliances can save up to 50% on your current heating costs! A heater as needed only provides hot water when you need it, so there is no need to hold heating water if you do not use it. No more heating bills day and night.

เครื่องทําน้ําอุ่น


On-demand heaters are also cheap heaters because they do not wear out like traditional tank units. Traditional units have a typical service life of 6 to 12 years before they need to be replaced.

A tank-free water heater can last 20 years or more, as it does not have hot water that "sits" in the tank and corrodes the interior. Scale and hard water deposits can greatly reduce the life and efficiency of a tank heater.

Tankless heaters also save space. They take up much less space than their traditional counterparts. Imagine having your water heater hanging on the wall and only taking up the space that a briefcase takes up!

Another advantage of this type of cheap water heater is its safety registration. Traditional tank heaters require you to set a minimum temperature, which is often much higher than you actually need. By using heaters, you can set the temperature where you want to use them, avoid combustion problems and further loss of energy.

Water heater installation

How to install your water heater

Let me guess, you went downstairs to check clothes or grab a tool and there it was. A large pool of water runs all over the basement floor and comes from the bottom of the water heater. This is the obvious and most common sign that you need a new water heater installation.

If you have any experience with DIY projects around the house, installing a new water heater shouldn't be a problem for you. Follow the steps in this article and you will have your new water heater installed in a couple of hours. Installing a water heater yourself will save you up to $ 300 to $ 400 depending on where you live. Now, if you are not very fond of it, you can install your own water tank, however it may take a little more than a few hours If you like challenges and are not afraid to do repairs in your home, you can also install the heater yourself same.

เครื่องทําน้ําอุ่น


Tools and Materials You Will Need:

Water Heater: Install What You Are Pulling Out If you have a 40 gallon and want to upgrade to 50 gallons, now is the time to do it. If you have a 50 gallon, I do NOT recommend switching to a lower one than you have.

¾ Connections - You will need 2 ¾ couplings and possibly some elbows. Check what type of plumbing you have that goes to your water heater. It can be copper, CPVC, PEX, or galvanized. I recommend getting Shark Bite fittings ¾ because they are so easy to install with PEX, CPVC, and copper pipe. When you have galvanized pipe, you may need to get a conversion fitting and fit one of the other pipes to make installation easier.

Black Pipe Fittings - You may need some ½ black pipe couplings and elbows to extend or shorten the gas line that connects to the heater. I install the gas line last. This way I will know exactly what I need for the gas connections.

2 - ¾ dielectrics. Always replace dielectrics when installing a new water heater. Make sure you get the right dielectrics for the pipe material you have in your home.

T&P Valve generally comes with the newer heaters.

Torch, flux, solder, sandpaper

Padlocks or elbow pliers

Pipe wrench

Pipe Thread Solution or Teflon Tape

Garden hose.

Now that we have all of our materials, let's get started. The first step is to turn off the main water supply to the house. Next Turn off the gas valve on the gas line to the เครื่องทําน้ําอุ่น. Now connect the garden hose to the bottom of the water heater and place the hose in the nearby floor drain. Turn on the valve (it looks like an outside hose faucet) and let the heater begin to drain.

At this time, go around your house and turn on all the taps. Make sure you leave the taps in the on position and have the hot and cold water running. This will allow all the water to drain from the heater much faster.

While the water is draining from the old heater, unpack the new water heater. First pipe the two shafts coming out of the top of the heater. Once they are doped, screw in the new dielectrics. Next, if your heater came with a T&P valve, unpack it and soak the threads. Screw the T&P valve into the side of the heater, there will be a threaded hole where it goes. You may need to use your socket wrench to turn the last one so the valve is pointing down. You now have the heater ready and ready to go.

water heater


Once the old heater has finished draining, disconnect the gas line at the union connection. This is the accessory that has a hexagonal center. Once the union is disconnected, disconnect the rest of the tubing ONLY on the heater you are replacing.

Now we will disconnect the water pipes. Use your channel locks to disconnect the dielectric. They will be disconnected like the gas pipe union fittings. Cut old dielectrics from copper or other tubing you may have.

Once all the pipes are disconnected from the water heater and there appears to be no more water in the tank, begin removing the old water heater. Make sure you leave enough room to put the new heater in place. If you have a small area, you may need to simply remove the old water heater to make room for the new water heater.

Align the new water heater with the pipes connecting the old heater. If you find that you need to change some water pipes, leave the pipe with the cold water valve on the straight pipe and reconfigure the hot side.

Connect the water line to the new heater using the shark bite fittings or whatever fittings you have.